--- (6) Debian6.0(Squeeze) 導入---
d) Squeezeの起動
(c)へ戻る ＜＝ ＝＞(a)へ帰る
---------------------------------------------------
色分け： 黒：画面表示 赤：入力 青：コメント
---------------------------------------------------
Orion1 CPU = Low
=== KURO U-Boot. ===
** LOADER **
** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
<<system_bootend>>
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: ST94813AS Firm: 3.06 Ser#: 5PJ3M4H4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38154.3 MB = 37.2 GB (78140160 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
1314928 bytes read
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/initrd.buffalo
2403828 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Debian kernel
Created: 2011-12-15 17:02:11 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1314864 Bytes = 1.3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02000000 ...
Image Name: Debian ramdisk
Created: 2011-12-15 17:02:11 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 2403764 Bytes = 2.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-orion5x (Debian 2.6.32-39) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Thu Nov 3 23:01:37 UTC 2011
[ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Buffalo/Revogear Kurobox Pro
[ 0.000000] Clearing invalid memory bank 0KB@0xffffffff
[ 0.000000] Clearing invalid memory bank 0KB@0xffffffff
[ 0.000000] Clearing invalid memory bank 0KB@0xffffffff
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x41000403
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 123404KB available (3224K code, 574K data, 128K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64
[ 0.000000] Console: colour dummy device 80x30
[ 25.770090] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 26.009962] Security Framework initialized
[ 26.010009] SELinux: Disabled at boot.
[ 26.010071] Mount-cache hash table entries: 512
[ 26.010816] Initializing cgroup subsys ns
[ 26.010850] Initializing cgroup subsys cpuacct
[ 26.010878] Initializing cgroup subsys devices
[ 26.010906] Initializing cgroup subsys freezer
[ 26.010932] Initializing cgroup subsys net_cls
[ 26.011058] CPU: Testing write buffer coherency: ok
[ 26.012780] devtmpfs: initialized
[ 26.016222] regulator: core version 0.5
[ 26.016691] NET: Registered protocol family 16
[ 26.017818] Orion ID: MV88F5182-A2. TCLK=166666667.
[ 26.019813] Applying Orion-1/Orion-NAS PCIe config read transaction workaround
[ 26.020350] PCI: bus0: Fast back to back transfers disabled
[ 26.023946] bio: create slab <bio-0> at 0
[ 26.024761] vgaarb: loaded
[ 26.026354] Switching to clocksource orion_clocksource
[ 26.040472] NET: Registered protocol family 2
[ 26.041108] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 26.043367] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 26.043626] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 26.043766] TCP: Hash tables configured (established 4096 bind 4096)
[ 26.043794] TCP reno registered
[ 26.044226] NET: Registered protocol family 1
[ 26.044734] Unpacking initramfs...
[ 26.512968] Freeing initrd memory: 2344K
[ 26.513169] NetWinder Floating Point Emulator V0.97 (double precision)
[ 26.513904] audit: initializing netlink socket (disabled)
[ 26.513985] type=2000 audit(0.730:1): initialized
[ 26.533286] VFS: Disk quotas dquot_6.5.2
[ 26.534035] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 26.534391] msgmni has been set to 245
[ 26.536250] alg: No test for stdrng (krng)
[ 26.536645] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 26.536685] io scheduler noop registered
[ 26.536709] io scheduler anticipatory registered
[ 26.536733] io scheduler deadline registered
[ 26.537305] io scheduler cfq registered (default)
[ 26.554173] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 26.555382] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
[ 26.899921] console [ttyS0] enabled
[ 26.904098] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
[ 26.911905] physmap platform flash device: 00040000 at f4000000
[ 26.918091] Found: SST 39LF020
[ 26.921168] physmap-flash.0: Found 1 x8 devices at 0x0 in 8-bit bank
[ 26.927606] number of JEDEC chips: 1
[ 26.931184] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
[ 26.952309] RedBoot partition parsing not available
[ 26.959116] NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)
[ 26.967883] Scanning device for bad blocks
[ 27.049001] Creating 3 MTD partitions on "orion_nand":
[ 27.054152] 0x000000000000-0x000000400000 : "uImage"
[ 27.060564] 0x000000400000-0x000004400000 : "rootfs"
[ 27.066958] 0x000004400000-0x000010000000 : "extra"
[ 27.074217] mice: PS/2 mouse device common for all mice
[ 27.080166] i2c /dev entries driver
[ 27.087463] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
[ 27.094572] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
[ 27.102010] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 27.146565] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 27.186546] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 27.195560] TCP cubic registered
[ 27.198854] NET: Registered protocol family 17
[ 27.203339] VFP support v0.3: not present
[ 27.208209] registered taskstats version 1
[ 27.214226] rtc-rs5c372 0-0032: setting system clock to 2011-12-15 21:01:25 UTC (1323982885)
[ 27.222871] Initalizing network drop monitor service
[ 27.228064] Freeing init memory: 128K
Loading, please wait...
[ 27.435673] udev[42]: starting version 164
[ 28.253060] SCSI subsystem initialized
[ 28.600862] sata_mv sata_mv.0: version 1.28
[ 28.606067] sata_mv sata_mv.0: slots 32 ports 2
[ 28.612354] scsi0 : sata_mv
[ 28.617150] scsi1 : sata_mv
[ 28.621431] ata1: SATA max UDMA/133 irq 29
[ 28.625539] ata2: SATA max UDMA/133 irq 29
[ 29.136485] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 29.176546] ata1.00: ATA-7: ST94813AS, 3.06, max UDMA/133
[ 29.181957] ata1.00: 78140160 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 29.246760] ata1.00: configured for UDMA/133
[ 29.251782] scsi 0:0:0:0: Direct-Access ATA ST94813AS 3.06 PQ: 0 ANSI: 5
[ 29.606496] ata2: SATA link down (SStatus 0 SControl 300)
[ 29.709334] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 29.720115] sd 0:0:0:0: [sda] Write Protect is off
[ 29.725317] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 29.736352] sda: sda1 sda2 sda3 < sda5 >
[ 29.861018] sd 0:0:0:0: [sda] Attached SCSI disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 30.878470] kjournald starting. Commit interval 5 seconds
[ 30.884012] EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd[ 32.743433] udev[144]: starting version 164
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[ 33.885693] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 33.892115] mv643xx_eth smi: probed
[ 33.986835] net eth0: port 0 with MAC address 00:16:01:a4:dc:1a
[ 34.396383] usbcore: registered new interface driver usbfs
[ 34.416894] usbcore: registered new interface driver hub
[ 34.431058] usbcore: registered new device driver usb
[ 34.505175] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 35.000750] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 35.015156] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 35.046505] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
[ 35.066457] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 35.072503] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 35.079361] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 35.086625] usb usb1: Product: Marvell Orion EHCI
[ 35.091333] usb usb1: Manufacturer: Linux 2.6.32-5-orion5x ehci_hcd
[ 35.097639] usb usb1: SerialNumber: orion-ehci.0
[ 35.105262] usb usb1: configuration #1 chosen from 1 choice
[ 35.111905] hub 1-0:1.0: USB hub found
[ 35.115748] hub 1-0:1.0: 1 port detected
[ 35.120172] orion-ehci orion-ehci.1: Marvell Orion EHCI
[ 35.125472] orion-ehci orion-ehci.1: new USB bus registered, assigned bus number 2
[ 35.156577] orion-ehci orion-ehci.1: irq 12, io mem 0xf10a0000
[ 35.176458] orion-ehci orion-ehci.1: USB 2.0 started, EHCI 1.00
[ 35.182507] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 35.189349] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 35.196610] usb usb2: Product: Marvell Orion EHCI
[ 35.201319] usb usb2: Manufacturer: Linux 2.6.32-5-orion5x ehci_hcd
[ 35.207642] usb usb2: SerialNumber: orion-ehci.1
[ 35.217950] usb usb2: configuration #1 chosen from 1 choice
[ 35.225440] hub 2-0:1.0: USB hub found
[ 35.230563] hub 2-0:1.0: 1 port detected
done.
Activating swap...[ 35.856401] Adding 368632k swap on /dev/sda5. Priority:-1 extents:1 across:368632k
done.
Checking root file system...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda2: clean, 21886/2403744 files, 315892/9612544 blocks
done.
[ 36.453446] EXT3 FS on sda2, internal journal
Cleaning up ifupdown....
[ 36.994949] loop: module loaded
Loading kernel modules...done.
Setting up networking....
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
e2fsck 1.41.12 (17-May-2010)
/dev/sda1: clean, 19/124496 files, 24000/248832 blocks
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Setting kernel variables ...done.
Configuring network interfaces...done.
Starting portmap daemon....
Starting NFS common utilities: statd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Starting portmap daemon...Already running..
Starting NFS common utilities: statd.
Starting enhanced syslogd: rsyslogd.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: cron.
[ 42.877480] eth0: link up, 1000 Mb/s, full duplex, flow control disabled
Starting Daemon for Linkstation/Kuro micro controller: micro-evtd.
[ 44.661557] NET: Registered protocol family 10
Starting OpenBSD Secure Shell server: sshd.
Starting MTA: exim4.
[ 53.254671] eth0: link up, 1000 Mb/s, full duplex, flow control disabled
Debian GNU/Linux 6.0 debian ttyS0
debian login: root
Password:****** /* インストール中に設定したパスワード*/
Linux debian 2.6.32-5-orion5x #1 Thu Nov 3 23:01:37 UTC 2011 armv5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~#root@debian:~# cd /
root@debian:/# ls
bin dev home lost+found mnt proc sbin srv tmp var
boot etc lib media opt root selinux sys usr
root@debian:/#
root@debian:/# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 37G 645M 34G 2% /
tmpfs 62M 0 62M 0% /lib/init/rw
udev 61M 68K 61M 1% /dev
tmpfs 62M 0 62M 0% /dev/shm
/dev/sda1 228M 8.2M 208M 4% /boot
root@debian:/#
(c)へ戻る ＜＝
Return
2011/12/21